Question: What Is A Toe Kick Plate?

A toe kick is the area between the base cabinet and the floor.

It is also referred to as the toe space.

A toe kick is the recessed area at the bottom of a base cabinet.

Toe kicks are built into bathroom vanities and kitchen cabinets to allow homeowners to be more comfortable as they are working on the counter-top.

Is a toe kick necessary?

The toe kick is typically only 3 inches deep and about 3 1/2 inches high, yet it makes a huge difference in the comfort of using your countertop. Although toe kicks are not required by building codes, they are a traditional design standard followed by manufacturers and tradesmen.

What color should the toe kick be?

In most kitchens the toe kick is either painted black or the same color as the cabinets, to make it as inconspicuous as possible.

How do you replace a toe kick?

How to Remove a Toe Kick From Base Cabinets

  • Position the end of the pry bar between the top of the quarter-round molding and the toe kick board. Tap the pry bar with a hammer to loosen the molding from the toe kick.
  • Find a joint or an end for the toe kick to start prying.
  • Loosen the toe kick board across its length.

How far back is a toe kick?

Standard Dimensions for Toe Kicks

Toe-kick depths greater than 3 inches do not hurt the effectiveness of the toe kick, but depths less than 3 inches should usually be avoided, as they interfere with ergonomic effectiveness. The optimal height for a toe kick is 3 1/2 inches, and heights up to 4 inches are common.

What is the purpose of a toe kick?

A toe kick is the area between the base cabinet and the floor. It is also referred to as the toe space. A toe kick is the recessed area at the bottom of a base cabinet. Toe kicks are built into bathroom vanities and kitchen cabinets to allow homeowners to be more comfortable as they are working on the counter-top.

What is a toe plate?

Noun. toeplate (plural toeplates) A metal plate used to strengthen the front portion of the sole of a shoe.

What is a kickboard in kitchen?

A toe kick or kickboard (in the kitchen cabinetry sense) is a fascia that fits across the recess at the bottom of a floor-mounted base cabinet; these serve to conceal the plinths / supports of cabinet leg systems.

How do you cut a toe kick?

Transfer the measurement to the back of the toe kick board. Use a miter saw to cut a 45-degree inside miter cut if the end of the toe kick board butts up to another cabinet run. Make a straight, 90-degree cut if cutting a toe kick board for a straight length of cabinets.

How do you attach a kick plate?

Hold the kick plate in position and insert screws into the top and bottom holes at the center of the plate. Tighten the screws securely. Install the remainder of the screws, working out toward either edge of the plate. This procedure helps prevent warping of the plate so that it will install flat against the door.

How do you take off a kick board?

Wedge the straight end of the pry bar under the toe kick board at an angle and then tap the other end with the hammer until it loosens and comes free from the base of the cabinet. Use the curved end of the pry bar the pull the board away.

How much should a countertop overhang?

The standard overhang of an island countertop — on the side designed to sit at and tuck stools underneath — is 12 inches. If you plan to extend the counter farther, you need to add supports such as legs, or wood corbels or metal L-brackets that extend half the overhang’s distance.

What is IKEA plinth?

IKEA does not offer integrated toe-kicks, also known as plinths, so you can forget about them for now. Instead, the base kitchen cabinets use adjustable legs you attach to the bottom of the cabinets. IKEA plinth seen from below. The good news: The legs can be adjusted individually to level the cabinets.

How high should a kick plate be?

Standard kick plates are either 6 or 8 inches tall. If your door has fewer than 8 1/2 inches between the bottom and the decoration, select a 6-inch kick plate. If it has fewer than 6 1/2 inches, custom order a kick plate to fit in the space.